Results 1 to 8 of 8

Thread: Joe's AEG clearing. Guns, Mags, and tons of parts.

  1. #1
    Non-WAA Contributor
    Join Date
    Aug 09
    Location
    Racine, WI
    Posts
    230
    Thanks
    0
    Thanked 0 Times in 0 Posts
    groans
    0
    groaned 0 Times in 0 Posts

    Default Joe's AEG clearing. Guns, Mags, and tons of parts.

    Putting all AEG stuff up for sale. PREFER TO DO DEALS FACE TO FACE, willing to meet within a reasonable distance. Will ship if you absolutely want to at your expense.

    First up is my baby. Started out life as a CA Sportline, however over the years due to unexpected breakage and wanting to make it cooler, very little factory parts remain.

    Run down of what it has:

    Echo1 gears
    Echo1 large bore nozzle
    Solid steel bearings
    JBU aluminum ball bearing piston head and cylinder head set
    Modify Ball bearing spring guide
    Dboy hop up bucking and nub (Can include a hard and soft bucking with nubs)
    Metal hop up chamber (1 piece)
    G&P Polycarb piston (5 or so metal teeth)
    Stock CA cylinder (for standard rifle length M4 carbine)
    285mm 6.04 tightbore barrel
    Extremefire MOSFET with Active Braking and Thermal Fuse (top of the line electronics)
    M90 spring
    Full metal body
    CQB length barrel
    Free float rail system
    Railed gas block and mock gas tube
    Crane stock
    2x 9.6v 1500mAh crane stock batteries
    8 Mag mid caps
    1 metal mid cap
    2 or 3 high caps
    CQB buffer tube sling plate for one point slings
    I did do all the custom 2 tone

    All my mags feel very well, and its running around 330-340fps for indoor CQB. HOWEVER- I WILL include another spring of your choice upon purchase. I have a few ranging from m95 to m120. A word of caution, this gearbox setup is so efficient that when I had a stock CA sportline spring in it (guessing M100) it was shooting ~420 fps.

    The gearbox has been well maintained and only teflon AEG gearbox grease has been used in it. The metal body shows signs of battle, but isnt too bad. Otherwise the only other flaw is that the crane stock butt pad must be held on with a long zip tie. But when you cut the excess off, it looks fine- I promise! Although this rifle is 4 years old, it HAS NOT been fielded for the past 2 years due to my airsoft hiatus. I just charged up one battery today and it fired no problem. I will get it back on my chrono later and add that official info soon.

    This gun has been built using TONS of my time and it did aide in the reason why I'm getting divorced. Thats how much I put into building it. the cost to build this rifle new would be at least $700 new, not including mags.

    $500 for the gun, mags, and any other small parts you could need (various small springs, tappets, shims, misc. external and internal parts including some inner and one M4 outer barrel)


    Next up is a lower receiver to the Echo1 Zombat. The upper broke, but the Lower can be used in conjunction with most uppers. I know G&P wont work, the take down holes are too far apart.
    $35



    Now we have an odd one... A G&G Scar L AEG body. Its missing some parts and screws, but mostly there. A few things about the G&G Scar is that the bolt catch works to hold the "bolt" back to adjust the hop up. And from what I remember the upper is made of either pure magnesium, or magnesium alloy to keep it light. This would really be good for someone who has a tan Scar, and wants to convert it to a black one. only comes with whats in the picture, and a Scar selector plate for a V2 box if so desired. Remember guys, this is a FULL TRADEMARKED RIFLE, and the complete gun retails for $380. Asking $50 and I will also include any small bits and pieces you may want as i mentioned in my M4 sale.





    I do have 2 more guns to sell, but I have to finish building one and track down what parts are in the other one. But I know that one to build was about $1k.

    Thanks for looking. Only trades that I will even remotely consider are CQB GBBRs with mags. Prefer M4 or scar variants. If you really want me to drool, you better have a KAC PDW long version in black.
    Last edited by Nemesis II; 26 Aug 12 at 12:58 PM.
    --------------------------------------
    M4A1 CQB- Frankensteined from a bunch of stuff...
    ...This signature small enough?

  2. #2
    Non-WAA Contributor
    Join Date
    Aug 09
    Location
    Racine, WI
    Posts
    230
    Thanks
    0
    Thanked 0 Times in 0 Posts
    groans
    0
    groaned 0 Times in 0 Posts

    Default

    All is still for sale.
    --------------------------------------
    M4A1 CQB- Frankensteined from a bunch of stuff...
    ...This signature small enough?

  3. #3
    Non-WAA Contributor
    Join Date
    Aug 09
    Location
    Racine, WI
    Posts
    230
    Thanks
    0
    Thanked 0 Times in 0 Posts
    groans
    0
    groaned 0 Times in 0 Posts

    Default

    Some o the stuff laying around. Mags included with gun. I may take things off the market, because I may build another gun out of this mess.


    3 hi caps



    1 metal mid cap



    8 MAG mid caps (all work/ feed perfect last I checked)




    Standard LE M4 stocks and buffer tubes, motor grip, flash hiders.



    CAR hand guards, and rail covers.



    Old TM plastic body (tan) and CA plastic body.



    A couple of M4 length metal outer barrels.

    --------------------------------------
    M4A1 CQB- Frankensteined from a bunch of stuff...
    ...This signature small enough?

  4. #4
    Non-WAA Contributor
    Join Date
    Aug 09
    Location
    Racine, WI
    Posts
    230
    Thanks
    0
    Thanked 0 Times in 0 Posts
    groans
    0
    groaned 0 Times in 0 Posts

    Default

    M4 price drop $450
    --------------------------------------
    M4A1 CQB- Frankensteined from a bunch of stuff...
    ...This signature small enough?

  5. #5
    Non-WAA Contributor
    Join Date
    Aug 09
    Location
    Racine, WI
    Posts
    230
    Thanks
    0
    Thanked 0 Times in 0 Posts
    groans
    0
    groaned 0 Times in 0 Posts

    Default

    M4 now $400 with all the stuff.

    Bumpski
    --------------------------------------
    M4A1 CQB- Frankensteined from a bunch of stuff...
    ...This signature small enough?

  6. #6
    Non-WAA Contributor
    Join Date
    Aug 09
    Location
    Racine, WI
    Posts
    230
    Thanks
    0
    Thanked 0 Times in 0 Posts
    groans
    0
    groaned 0 Times in 0 Posts

    Default

    Bump

    $350
    --------------------------------------
    M4A1 CQB- Frankensteined from a bunch of stuff...
    ...This signature small enough?

  7. #7
    Non-WAA Contributor
    Join Date
    Aug 09
    Location
    Racine, WI
    Posts
    230
    Thanks
    0
    Thanked 0 Times in 0 Posts
    groans
    0
    groaned 0 Times in 0 Posts

    Default

    Come on! Gun, mags, batteries, and charger for $350
    --------------------------------------
    M4A1 CQB- Frankensteined from a bunch of stuff...
    ...This signature small enough?

  8. #8
    Non-WAA Contributor
    Join Date
    Aug 09
    Location
    Racine, WI
    Posts
    230
    Thanks
    0
    Thanked 0 Times in 0 Posts
    groans
    0
    groaned 0 Times in 0 Posts

    Default

    Gun, mags, batteries, and charger for $300. It a f***ing steal. Buy this!
    --------------------------------------
    M4A1 CQB- Frankensteined from a bunch of stuff...
    ...This signature small enough?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •